|  | | | |
| Products | Introduction | Order Qty | Select | | | Line Interactive UPS | | KIN-500C | Function & Characteristic
1.Main circuit is controlled by microprocessor(CPU)
2.Line interactive design.
3.LED status display.
4.AVR function
5.Over-discharge protection: After battery discharged, UPS will cut off the power and battery stop discharging. When Mains recover, UPS can autostart and charge the battery instantaneously, no harm to battery.
6.User-Replaceable Battery Design.
7.Cold start function(DC power on).
8.Provides lightning, surge, overload and short-circuit protection.
9.Automatically fault checks when starts, to increase the rate of safe use.
10.Special design of the charging mode, even when UPS is in fault or shut off, the charging circuit can still work properly and adjust the charging mode(Floating charge or continuous charge)to prolong the working life of the battery.
11.Tel./Modem/Fax/internet surge suppression.
12.Optional Bundle Software Automatically save your valuable files before auto shutdown.Primary Technical Parameter
Capacity:500VA/300W
Input voltage:85VAC-135VAC or 165VAC-275VAC
Input frequency:50Hz+/-5% or 60Hz+/-5%
Output voltage:110VAC or 220VAC
Output voltage regulation:+/-6%
Output frequency:50Hz or 60Hz
Output frequency regulation:+/-1Hz
Output waveform:Modified sine wave
Output power factor:0.6
Output transfer time:Less than 4ms(typical)
Battery type:12V/7AH/1PC
Battery back-up time:(a PC with 15" monitor):20 minutes
Battery recharge time:10 hours
Battery terminated voltage:9.2+/-0.2V
Indicator:LED indicator for line on, battery back-up, UPS cut off
Alarm for battery back-up:Sounding every 3 seconds
Alarm for battery low:Sounding every 1 second
Alarm for overload:Continue beeping sound
Overload protection:Fuse¤t limited
Short circuit protection:Fuse¤t limited&cut-off
Low battery protection:No battery drain after cut-off
Physical dimension(DxWxH):32.8x11.5x16cm; Physical net weight:6KGS
Operating Te |
| | | | | Line Interactive UPS | | KIN-500L | Function & Characteristic
1.Smart Microprocessor control
2.Line interactive design.
3.LED status display.
4.AVR function
5.Provides lightning, surge, overload and short-circuit protection.
6.User-Replaceable Battery Design.
7.Cold start function(DC power on).
8.Built-in power purify circuit restrain distorion of lightning strike, pulse and miscellaneous wave etc.
9.Tel./Modem/Fax/Internet surge suppression.
10.Optional Bundle Software Automatically save your valuable files before auto shutdown.Primary Technical Parameter
Capacity:500VA/300W
Input voltage:85VAC-135VAC or 165VAC-275VAC
Input frequency:50Hz+/-5% or 60Hz+/-5%
Output voltage:110VAC or 220VAC
Output voltage regulation:+/-6%
Output frequency:50Hz or 60Hz
Output frequency regulation:+/-1Hz
Output waveform:Modified sine wave
Output power factor:0.6
Output transfer time:Less than 4ms(typical)
Battery type:12V/7AH/1PC
Battery back-up time:(a PC with 15" monitor):20 minutes
Battery recharge time:10 hours
Battery terminated voltage:9.2+/-0.2V
Indicator:LED indicator for line on, battery back-up, UPS cut off
Alarm for battery back-up:Sounding every 3 seconds
Alarm for battery low:Sounding every 1 second
Alarm for overload:Continue beeping sound
Overload protection:Fuse¤t limited
Short circuit protection:Fuse¤t limited&cut-off
Low battery protection:No battery drain after cut-off
Physical dimension(DxWxH):32.8x11.5x16cm; Physical net weight:6KGS
Operating Temperature:32°F-104°F at full load, 0-90% relative humidity(-5℃-40℃)(non-condensing)
Noise level:Less than 40db(at 1 meter)
Interface contact closure:DB9 connector for connecting with UPS software
Interface software: Rups 2000(Option)
Tel./Moderm/Fax/Internet:RJ11/RJ45 |
| | | | | Line Interactive UPS | | KIN-600C | Function & Characteristic
1.Main circuit is controlled by microprocessor(CPU)
2.Line interactive design.
3.LED status display.
4.AVR function
5.Over-discharge protection: After battery discharged, UPS will cut off the power and battery stop discharging. When Mains recover, UPS can autostart and charge the battery instantaneously, no harm to battery.
6.User-Replaceable Battery Design.
7.Cold start function(DC power on).
8.Provides lightning, surge, overload and short-circuit protection.
9.Automatically fault checks when starts, to increase the rate of safe use.
10.Special design of the charging mode, even when UPS is in fault or shut off, the charging circuit can still work properly and adjust the charging mode(Floating charge or continuous charge)to prolong the working life of the battery.
11.Tel./Modem/Fax/internet surge suppression.
12.Optional Bundle Software Automatically save your valuable files before auto shutdown.Primary Technical Parameter
Capacity:600VA/360W
Input voltage:85VAC-135VAC or 165VAC-275VAC
Input frequency:50Hz+/-5% or 60Hz+/-5%
Output voltage:110VAC or 220VAC
Output voltage regulation:+/-6%
Output frequency:50Hz or 60Hz
Output frequency regulation:+/-1Hz
Output waveform:Modified sine wave
Output power factor:0.6
Output transfer time:Less than 4ms(typical)
Battery type:12V/7AH/1PC
Battery back-up time:(a PC with 15" monitor):20 minutes
Battery recharge time:10 hours
Battery terminated voltage:9.2+/-0.2V
Indicator:LED indicator for line on, battery back-up, UPS cut off
Alarm for battery back-up:Sounding every 3 seconds
Alarm for battery low:Sounding every 1 second
Alarm for overload:Continue beeping sound
Overload protection:Fuse¤t limited
Short circuit protection:Fuse¤t limited&cut-off
Low battery protection:No battery drain after cut-off
Physical dimension(DxWxH):32.8x11.5x16cm; Physical net weight:6.5KGS
Operating |
| | | | | Line Interactive UPS | | KIN-600L | Function & Characteristic
1.Smart Microprocessor control
2.Line interactive design.
3.LED status display.
4.AVR function
5.Provides lightning, surge, overload and short-circuit protection.
6.User-Replaceable Battery Design.
7.Cold start function(DC power on).
8.Built-in power purify circuit restrain distorion of lightning strike, pulse and miscellaneous wave etc.
9.Tel./Modem/Fax/Internet surge suppression.
10.Optional Bundle Software Automatically save your valuable files before auto shutdown.Primary Technical Parameter
Capacity:600VA/360W
Input voltage:85VAC-135VAC or 165VAC-275VAC
Input frequency:50Hz+/-5% or 60Hz+/-5%
Output voltage:110VAC or 220VAC
Output voltage regulation:+/-6%
Output frequency:50Hz or 60Hz
Output frequency regulation:+/-1Hz
Output waveform:Modified sine wave
Output power factor:0.6
Output transfer time:Less than 4ms(typical)
Battery type:12V/7AH/1PC
Battery back-up time:(a PC with 15" monitor):20 minutes
Battery recharge time:10 hours
Battery terminated voltage:9.2+/-0.2V
Indicator:LED indicator for line on, battery back-up, UPS cut off
Alarm for battery back-up:Sounding every 3 seconds
Alarm for battery low:Sounding every 1 second
Alarm for overload:Continue beeping sound
Overload protection:Fuse¤t limited
Short circuit protection:Fuse¤t limited&cut-off
Low battery protection:No battery drain after cut-off
Physical dimension(DxWxH):32.8x11.5x16cm; Physical net weight:6.5KGS
Operating Temperature:32°F-104°F at full load, 0-90% relative humidity(-5℃-40℃)(non-condensing)
Noise level:Less than 40db(at 1 meter)
Interface contact closure:DB9 connector for connecting with UPS software
Interface software: Rups 2000(Option)
Tel./Moderm/Fax/Internet:RJ11/RJ45 |
| | | | | Line Interactive UPS | | KIN-650C | Function & Characteristic
1.Main circuit is controlled by microprocessor(CPU)
2.Line interactive design.
3.LED status display.
4.AVR function
5.Over-discharge protection: After battery discharged, UPS will cut off the power and battery stop discharging. When Mains recover, UPS can autostart and charge the battery instantaneously, no harm to battery.
6.User-Replaceable Battery Design.
7.Cold start function(DC power on).
8.Provides lightning, surge, overload and short-circuit protection.
9.Automatically fault checks when starts, to increase the rate of safe use.
10.Special design of the charging mode, even when UPS is in fault or shut off, the charging circuit can still work properly and adjust the charging mode(Floating charge or continuous charge)to prolong the working life of the battery.
11.Tel./Modem/Fax/internet surge suppression.
12.Optional Bundle Software Automatically save your valuable files before auto shutdown.Primary Technical Parameter
Capacity:650VA/390W
Input voltage:85VAC-135VAC or 165VAC-275VAC
Input frequency:50Hz+/-5% or 60Hz+/-5%
Output voltage:110VAC or 220VAC
Output voltage regulation:+/-6%
Output frequency:50Hz or 60Hz
Output frequency regulation:+/-1Hz
Output waveform:Modified sine wave
Output power factor:0.6
Output transfer time:Less than 4ms(typical)
Battery type:12V/7AH/1PC
Battery back-up time:(a PC with 15" monitor):20 minutes
Battery recharge time:10 hours
Battery terminated voltage:9.2+/-0.2V
Indicator:LED indicator for line on, battery back-up, UPS cut off
Alarm for battery back-up:Sounding every 3 seconds
Alarm for battery low:Sounding every 1 second
Alarm for overload:Continue beeping sound
Overload protection:Fuse¤t limited
Short circuit protection:Fuse¤t limited&cut-off
Low battery protection:No battery drain after cut-off
Physical dimension(DxWxH):32.8x11.5x16cm; Physical net weight:6.7KGS
Operating |
| | | | | Line Interactive UPS | | KIN-650L | Function & Characteristic
1.Smart Microprocessor control
2.Line interactive design.
3.LED status display.
4.AVR function
5.Provides lightning, surge, overload and short-circuit protection.
6.User-Replaceable Battery Design.
7.Cold start function(DC power on).
8.Built-in power purify circuit restrain distorion of lightning strike, pulse and miscellaneous wave etc.
9.Tel./Modem/Fax/Internet surge suppression.
10.Optional Bundle Software Automatically save your valuable files before auto shutdown.Primary Technical Parameter
Capacity:650VA/390W
Input voltage:85VAC-135VAC or 165VAC-275VAC
Input frequency:50Hz+/-5% or 60Hz+/-5%
Output voltage:110VAC or 220VAC
Output voltage regulation:+/-6%
Output frequency:50Hz or 60Hz
Output frequency regulation:+/-1Hz
Output waveform:Modified sine wave
Output power factor:0.6
Output transfer time:Less than 4ms(typical)
Battery type:12V/7AH/1PC
Battery back-up time:(a PC with 15" monitor):20 minutes
Battery recharge time:10 hours
Battery terminated voltage:9.2+/-0.2V
Indicator:LED indicator for line on, battery back-up, UPS cut off
Alarm for battery back-up:Sounding every 3 seconds
Alarm for battery low:Sounding every 1 second
Alarm for overload:Continue beeping sound
Overload protection:Fuse¤t limited
Short circuit protection:Fuse¤t limited&cut-off
Low battery protection:No battery drain after cut-off
Physical dimension(DxWxH):32.8x11.5x16cm; Physical net weight:6.7KGS
Operating Temperature:32°F-104°F at full load, 0-90% relative humidity(-5℃-40℃)(non-condensing)
Noise level:Less than 40db(at 1 meter)
Interface contact closure:DB9 connector for connecting with UPS software
Interface software: Rups 2000(Option)
Tel./Moderm/Fax/Internet:RJ11/RJ45 |
| | | | | Line Interactive UPS | | KIN-1000C | Function & Characteristic
1.Main circuit is controlled by microprocessor(CPU)
2.Line interactive design.
3.LED status display.
4.AVR function
5.Over-discharge protection: After battery discharged, UPS will cut off the power and battery stop discharging. When Mains recover, UPS can autostart and charge the battery instantaneously, no harm to battery.
6.User-Replaceable Battery Design.
7.Cold start function(DC power on).
8.Provides lightning, surge, overload and short-circuit protection.
9.Automatically fault checks when starts, to increase the rate of safe use.
10.Special design of the charging mode, even when UPS is in fault or shut off, the charging circuit can still work properly and adjust the charging mode(Floating charge or continuous charge)to prolong the working life of the battery.
11.Tel./Modem/Fax/internet surge suppression.
12.Optional Bundle Software Automatically save your valuable files before auto shutdown.Primary Technical Parameter
Capacity:1000VA/600W
Input voltage:85VAC-135VAC or 165VAC-275VAC
Input frequency:50Hz+/-5% or 60Hz+/-5%
Output voltage:110VAC or 220VAC
Output voltage regulation:+/-6%
Output frequency:50Hz or 60Hz
Output frequency regulation:+/-1Hz
Output waveform:Modified sine wave
Output power factor:0.6
Output transfer time:Less than 4ms(typical)
Battery type:12V/7AH/2PCS
Battery back-up time:(a PC with 15" monitor):45 minutes
Battery recharge time:10 hours
Battery terminated voltage:9.2+/-0.2V
Indicator:LED indicator for line on, battery back-up, UPS cut off
Alarm for battery back-up:Sounding every 3 seconds
Alarm for battery low:Sounding every 1 second
Alarm for overload:Continue beeping sound
Overload protection:Fuse¤t limited
Short circuit protection:Fuse¤t limited&cut-off
Low battery protection:No battery drain after cut-off
Physical dimension(DxWxH):34x13.3x19.5cm; Physical net weight:11.6KGS
Operati |
| | | | | Line Interactive UPS | | KIN-1000L | Function & Characteristic
1.Smart Microprocessor control
2.Line interactive design.
3.LED status display.
4.AVR function
5.Provides lightning, surge, overload and short-circuit protection.
6.User-Replaceable Battery Design.
7.Cold start function(DC power on).
8.Built-in power purify circuit restrain distorion of lightning strike, pulse and miscellaneous wave etc.
9.Tel./Modem/Fax/Internet surge suppression.
10.Optional Bundle Software Automatically save your valuable files before auto shutdown.Primary Technical Parameter
Capacity:1000VA/600W
Input voltage:85VAC-135VAC or 165VAC-275VAC
Input frequency:50Hz+/-5% or 60Hz+/-5%
Output voltage:110VAC or 220VAC
Output voltage regulation:+/-6%
Output frequency:50Hz or 60Hz
Output frequency regulation:+/-1Hz
Output waveform:Modified sine wave
Output power factor:0.6
Output transfer time:Less than 4ms(typical)
Battery type:12V/7AH/2PCS
Battery back-up time:(a PC with 15" monitor):45 minutes
Battery recharge time:10 hours
Battery terminated voltage:9.2+/-0.2V
Indicator:LED indicator for line on, battery back-up, UPS cut off
Alarm for battery back-up:Sounding every 3 seconds
Alarm for battery low:Sounding every 1 second
Alarm for overload:Continue beeping sound
Overload protection:Fuse¤t limited
Short circuit protection:Fuse¤t limited&cut-off
Low battery protection:No battery drain after cut-off
Physical dimension(DxWxH):34x13.3x19.5cm; Physical net weight:11.6KGS
Operating Temperature:32°F-104°F at full load, 0-90% relative humidity(-5℃-40℃)(non-condensing)
Noise level:Less than 40db(at 1 meter)
Interface contact closure:DB9 connector for connecting with UPS software
Interface software: Rups 2000(Option)
Tel./Moderm/Fax/Internet:RJ11/RJ45 |
| | | | | Line Interactive UPS | | KIN-1200C | Function & Characteristic
1.Main circuit is controlled by microprocessor(CPU)
2.Line interactive design.
3.LED status display.
4.AVR function
5.Over-discharge protection: After battery discharged, UPS will cut off the power and battery stop discharging. When Mains recover, UPS can autostart and charge the battery instantaneously, no harm to battery.
6.User-Replaceable Battery Design.
7.Cold start function(DC power on).
8.Provides lightning, surge, overload and short-circuit protection.
9.Automatically fault checks when starts, to increase the rate of safe use.
10.Special design of the charging mode, even when UPS is in fault or shut off, the charging circuit can still work properly and adjust the charging mode(Floating charge or continuous charge)to prolong the working life of the battery.
11.Tel./Modem/Fax/internet surge suppression.
12.Optional Bundle Software Automatically save your valuable files before auto shutdown.Primary Technical Parameter
Capacity:1200VA/720W
Input voltage:85VAC-135VAC or 165VAC-275VAC
Input frequency:50Hz+/-5% or 60Hz+/-5%
Output voltage:110VAC or 220VAC
Output voltage regulation:+/-6%
Output frequency:50Hz or 60Hz
Output frequency regulation:+/-1Hz
Output waveform:Modified sine wave
Output power factor:0.6
Output transfer time:Less than 4ms(typical)
Battery type:12V/7AH/2PCS
Battery back-up time:(a PC with 15" monitor):45 minutes
Battery recharge time:10 hours
Battery terminated voltage:9.2+/-0.2V
Indicator:LED indicator for line on, battery back-up, UPS cut off
Alarm for battery back-up:Sounding every 3 seconds
Alarm for battery low:Sounding every 1 second
Alarm for overload:Continue beeping sound
Overload protection:Fuse¤t limited
Short circuit protection:Fuse¤t limited&cut-off
Low battery protection:No battery drain after cut-off
Physical dimension(DxWxH):34x13.3x19.5cm; Physical net weight:12KGS
Operating |
| | | | | Line Interactive UPS | | KIN-1200L | Function & Characteristic
1.Smart Microprocessor control
2.Line interactive design.
3.LED status display.
4.AVR function
5.Provides lightning, surge, overload and short-circuit protection.
6.User-Replaceable Battery Design.
7.Cold start function(DC power on).
8.Built-in power purify circuit restrain distorion of lightning strike, pulse and miscellaneous wave etc.
9.Tel./Modem/Fax/Internet surge suppression.
10.Optional Bundle Software Automatically save your valuable files before auto shutdown.Primary Technical Parameter
Capacity:1200VA/720W
Input voltage:85VAC-135VAC or 165VAC-275VAC
Input frequency:50Hz+/-5% or 60Hz+/-5%
Output voltage:110VAC or 220VAC
Output voltage regulation:+/-6%
Output frequency:50Hz or 60Hz
Output frequency regulation:+/-1Hz
Output waveform:Modified sine wave
Output power factor:0.6
Output transfer time:Less than 4ms(typical)
Battery type:12V/7AH/2PCS
Battery back-up time:(a PC with 15" monitor):45 minutes
Battery recharge time:10 hours
Battery terminated voltage:9.2+/-0.2V
Indicator:LED indicator for line on, battery back-up, UPS cut off
Alarm for battery back-up:Sounding every 3 seconds
Alarm for battery low:Sounding every 1 second
Alarm for overload:Continue beeping sound
Overload protection:Fuse¤t limited
Short circuit protection:Fuse¤t limited&cut-off
Low battery protection:No battery drain after cut-off
Physical dimension(DxWxH):34x13.3x19.5cm; Physical net weight:12KGS
Operating Temperature:32°F-104°F at full load, 0-90% relative humidity(-5℃-40℃)(non-condensing)
Noise level:Less than 40db(at 1 meter)
Interface contact closure:DB9 connector for connecting with UPS software
Interface software: Rups 2000(Option)
Tel./Moderm/Fax/Internet:RJ11/RJ45 |
| | |   |
| |
|